Supplier Spotlight

Video Exclusives

Holden V6 Twin Turbo test

Ahead of next season's new regulations, Holden tests its new 3.6 litre V6 twin-turbo at Norwell Motorplex




Acura - ARX-05 - Prototype preview

Ahead of its official unveiling on August 18, Acura has teased its forthcoming IMSA prototype, the ARX-05

'Are 'Balance of Performance' techniques worthwhile, or are there more effective ways of equalising a field's performance?'

Web Exclusive Articles

« back to listing

Selective laser sintering in motorsport components

CRP Group outlines how its new innovative SLS (Selective Laser Sintering) process helped create a conceptual front air inlet for a leading Moto3 racing team

Submitted by: CRP Technology

 

CRP Technology’s R&D department tackled the development of a new front air inlet for a Moto3 racing customer to solve space issues in the front fork area.

It has been manufactured in Windform materials by using an SLS Additive Manufacturing technique.

Testing had shown that increasing air flow to the air-box improved the performance of the engine at every RPM range. This led the team as well as the engineers to conclude that they need to design a new track ready inlet. This design would make the air inlet longer, and bring the opening up to the front side of the fairing, in order to have a direct air flow with less turbulence.

Among the goals to be achieved, was the need to avoid modifying the existing frame and the existing triple clamps. The design would have to fit to the existing platform in order to test the on-track advantages and disadvantages of using this solution, and to make a direct comparison with the current standard inlet.

Additive Manufacturing (SLS) and Windform materials allowed for:

  • Total freedom and no limitations in design (Design For functionality instead of design for manufacturing)
  • Creation of mock-up for assembling, fitting, and functionality
  • Production of parts for performance tests
  • Reduction in product and project realization timing

The final decision to use the new inlet came from its behavior on-track with the key points being it’s performance and reliability. Engineers kept the current airbox with the aim to mount the traditional air inlet as well as the new one and to acquire data of the airbox pressure on track.

(1)

(2)

1, 2: CAD files of the front air inlet

Front air inlet (final version) after testing. Outlined in red the zone where the front fork touched the inlet duct

The Project
Through the use of Reverse Engineering, the original airbox was scanned and virtually assembled with the CAD system.
This allowed the engineers to be able to create a new model of the air inlet by taking into account the amount of available space, and the constraints of the assembly of the current airbox and frame.

First Prototype
Once a first draft of the air inlet was developed, a prototype in Windform GF 2.0 was created. The decision to use Windform GF 2.0 was made to reduce costs, while being able to perform multiple tests with multiple prototypes.

First Prototype: The duct was mounted and required changes were marked. The flexible areas were adjusted to guarantee the minimum steering angle

The first prototype allowed engineers to see if the design fitment was correct and suitable for assembly. It was revealed by the first design that some sections needed to be changed due to the lack of space available under the lower triple clamp. This problem is further complicated when the bike is cornering and under braking conditions.

To optimize the volume of the inlet duct under the lower triple clamp, the engineers adopted a creative approach and decided to use a portion of the duct in Windform RL , the new rubber-like composite material produced by CRP Technology. This would be bonded to the main structure that was made out of Windform XT 2.0 for evaluation in racing conditions. To facilitate this they also carried out a bonding test to study the characteristics of the final assembly.

A bonding test was done to examine the joining of Windform RL to Windform XT 2.0 and GF 2.0

The concept was to make the bottom part of the duct with Windform RL in the fork and triple clamp area, and then assemble this into the top part produced in Windform XT 2.0. This approach would allow good clear airflow on the straightaway sections of the course, and thus an excellent flow to the airbox. Under breaking, the front fender could move up and collapse the inlet duct without any damages, due to the flexible material.

In addition, it was decided after examining the part that making the ducting flexible in the same area next to the front forks would off an additional benefit. The engineers were able to maximize the duct volume because the maximum steering actions are only reached when the bike is pushed into the paddock by the technical staff. In this situation, the front fork can tough the inlet duct deforming it without any damages.

Second Prototype
A second prototype was made in Windform GF 2.0. 

Comparison between the two prototypes. First prototype: outlined in yellow changes to be made. Second prototype: the flexible area has been redesigned (outlined in red) in order to ensure the mobility of the steering

Once the second prototype was mounded the engineers noticed some changes to be made, especially in the front fork area.

The soft section was too short and the forks could touch the area of the duct near the bonding overlap when steering travel was checked from lock to lock position. It was also seen that toward the back of the flexible area, near the airbox, that the duct was very close to the front wheel in the maximum braking position.

During testing it was determined that when the motorcycle was under severe braking, the front fender contact area on the duct in the soft part was too large. This situation, from the rider’s point of view, was not good because during hard braking, the steering must be free from movements, as the rider might need to correct the trajectory quickly.

The amount of input from the rider may be small, but it must occur very smoothly and too much contact of the front wheel assembly gave the impression of drag on steering. This affected the way the rider felt on the bike.

The team and engineers decided to change the inlet by reducing the portion that would make contact with the fender to reduce drag perceived by the rider.

(3) (4) 

(3.) Front air inlet- top part in Windform XT 2.0. (4.) Front air inlet-bottom part in Windform RL

The part made in Windform RL was enlarged according to the second test, and engineers and the rest of the team could get the correct fit for performance.

Front air inlet (final version) after testing. Outlined in red the zone where the front fork touched the inlet duct

In the final test version, Windform XT 2.0 was utilized in order to reduce the weight of the front and central part of the inlet, while the Windform RL material was used for the flexible part of the inlet. The two parts were bonded together after being produced.

Detail of the Front air inlet-bottom part in Windform RL (flexibility) after testing

Bonding
Bonding SLS parts is very important for the final result of the prototype: the right selection of bonding methods and adhesives will influence accuracy and functionality.

Bonding Details

 

Inlet duct mounted on the bike

 

 

Wiring in race cars is becoming more and more complex and Power Units are made up of several parts that need to be integrated into the final assembly. Available space is increasingly limited, so engineers are frequently utilizing flexible parts such as cooling ducts and wiring harnesses.

The solution outlined here can be easily applied to the automotive racing world.

 

Read Latest Issue

Web Exclusives

State of the art equipment from Gratnells Engineering has been praised for its role in making UGR-17 the most successful car in UGRacing history
Click here to read more

Sangha Racing explains how using Fintek's super finishing on its race transmission led to a 5% performance increase, less friction and improved reliability
Click here to read more

ARCA breaks down the incredible stats brought about by its switch to Ilmor engines and Five Star composites bodies after 50 races in the format
Click here to read more


Supplier Spotlight

Supplier SpotlightWe are building a list of leading suppliers covering all aspects of the professional motorsport industry. Want to see your company included? Contact aboobaker.tayub@ukimediaevents.com for more details.

فروشگاه اینترنتی فروشگاه اینترنتی سیستم همکاری در فروش کانال تلگرام چت روم فال حافظ دانلود فیلم فروشگظ;ه اینترنتی

Submit your industry opinion

Industry BlogDo you have an opinion you'd like to share with the professional motorsport community? We'd like to hear your views and opinions on the leading issues shaping the industry. Share your comments by sending up to 500 words to john.obrien@ukimediaevents.com

Submit Your Recruitment Ad

Recruitment AdTo send us your recruitment advertising or to receive information on placing a banner please email john.obrien@ukimediaevents.com